Author: gnadmin

OTC is the largest event in the world for the oil and gas industry. Every year, GN will attend the show and bring new products there. Likewise, GN team will be there again this May.

By the way, before the OTC, GN will take part the CIPPE 2018 first in Beijing from 27th to 29th March, 2018. For anybody who is not able to be Beijing can meet with GN at Houston.

Same as last year, GN will have 2 booths this year; please write down below information that will help you to GN’s booth.

Show Time & Location: 30 April – 3 May, 2018. NRG Park, Houston, Texas, USA
Booth No. 1: NRG Center 1369-1 (GN China)
Booth No. 2: NRG Arena 8000 (GN America)

For appointment with GN, please send email to sales@gnsolidscontrol.com or usa@gnsolidscontrol.com
GN’s office and warehouse in Houston can give a better support, for more information, please refer towww.gnsolidsamerica.com

GN Booth at OTC 2017

What GN will display at the show

1. Decanter Centrifuge GNLW363C – the best seller in GN’s production line. When design this model, GN choose to use the duplex stainless steel 2304 as the bowl material and centrifugal casting technology to make the bowl have a better dynamic balance. This 14 inch model is typically been used in solids control system, waste management system and dewatering system.
2. Shale Shaker GNZS594F – GN 4-panel-screen shale shaker is a widely accepted model with large screen and adjustable high G force. Patented sealing technology gives this model a better performance in preventing drilling fluids leak, which ensure the drying performance. Base on the shale shaker, the relative products mud cleaner and shaker screens will also be shown there. 
3. Sludge Pump GNSP-20A- this is a fully air driven pump that can be used in transferring high solids content and high gravity sludge. This pump is a safe pump that can be used in hazardous area. Without moving parts in the vacuum bag, the maintenance of the pump is also very convenient. GN will also show the widely used centrifugal pump at the show.

GN Shaker and Decanter Centrifuge Shown at OTC 2017

GN is looking forward to meet with all visitors at the OTC 2018.

Last week, GN sent one set 400 BBL capacity mud tank system for an Australia client. GN’s rich experience in manufacturing as per Australia standards, like welding, cable colors and so on, ensures this order. Client also approved and accepted when visited GN on inspection before delivery.

This 400 BBL mud system is for a small rig. Client was worrying about the height of the mud tank will be higher than the drilling mud return pipe of the rig. Actually, GN’s design team has lot of experience in design the mud system, this problem will be considered as one the key factors when make the design. After confirming the height, the proposal provided by GN has a full consideration on let the used drilling mud flow to the tank and ever get into the shale shaker unit easily.

This 400 BBL mud tank system is consisting of 3 parts. Mud recycling tank, mud storage tank and a separate mud mixing unit skid. In consideration of the sufficient tank net volume and height limitation, GN designed the tank with large width which can only be shipped by bulk ship. A separatemixing hopper skid is also for the purpose of making the tank larger net volume capacity.

The equipment configuration of this 400 BBL mud system is simple but effective. 2 unit GNZS703 shale shaker installed on the first tank for coarse solids separation, the shakers occupied almost half area of the tank top, the other half is fixed with one unit mud agitator and also left space for mounting a degasser unit in future in case any request. The second tank is used for active mud storage and mud mixing, four units mud agitators work well to keep the solids in drilling fluids suspending. A separate mixing unit skid is able to be connected with mud tank freely as per site area.

GN solids control has rich experience in designing and manufacturing the mud tank system used in oil gas drilling and other drilling projects. Any request, no hesitate to contact with GN.

GN Solids Control has rich experience in making compact mud recycling system that used in no-dig drilling project. GN has standard model of compact mud system for option, for clients’ special requirements, GN is able to provide customized solution. This week, GN completed the fabrication of one set 350GPM mud recycling system for a UAE client.
The 350GPM mud recycling system in this order is GN standard self-contained unit with mud recycling, storage and mixing function. The equipment configuration is as below:

1. Shaker and mud cleaner composition unit- this unit is the main mud recycling equipment. The shaker equipped in this unit is a double deck model, the under layer is used as the first stage mud recycling equipment for coarse solids separation. GN composite frame shaker screen could effectively remove the solid particles; this process could reduce the load for the cyclone unit. The drilling mud passing through the under layer screen will immediately transferred by a centrifugal pump unit to the 4 inch cyclone for fine solids separation. The drilling mud after treated by the cyclone, solids with size larger than around 20 microns would be removed. Discharged slurry will be further dried by the upper layer screen for more fluids recovery.

2. A mud tank will be used as the mounting support of the shaker unit, the feeding pump of cyclone and the mixing pump would be mounted on the tank skid as well. On top of the tank, a mud hopper will be installed as the mud chemicals adding port. The mud tank is divided into two parts respectively for sand trap, storage and mixing.

This 350GPM mud recycling system could be packed in one 40 feed container for sea transportation. GN is full of experience in designing and manufacturing the compact mud recycling system. Besides the self-contained model, GN also has economic desanding unit that is widely used in piling project. For more information, please feel free to contact with GN.

Couple months before, GN delivered 3 units of poor boy degasser to GNPC. Today GN finished another order of poor boy degasser from a France Client. GN’s poor boy degasser is manufactured as per API and ISO standard for underbalanced condition drilling to prevent dramatic pressure surges. For most of the deep drilling rig, a poor boy degasser is indispensable equipment for safety operation consideration. 
On oil drilling site, the poor boy degasser is always located beside the mud recycling system. In normal condition, the dirty mud back from well will go directly to the drilling mud shale shaker for solids separation. Under this condition, the poor boy degasser will not be applied. In case gas layer was intruded, a blowout might happen. This is the when the poor boy degasser will be used.

GN’s poor boy degasser is with simple structure for gas cut mud hitting on the baffle plates for dispersion, and then the gas separated The degasser unit could be designed to fix on a skid, thus the poor boy could be folded and easily moved on site. The chock manifold can also be installed on the skid. Before the drilling mud getting into the poor boy degasser, the chock manifold will reduce the pressure of the mud firstly.
Mostly, the poor boy degasser will be connected with an ignition device. The flammable and poisonous gas discharged from the poor boy degasser will be guided to the ignition device for burning out. Safety should be give the priority forever in any jobsite. 
GN Solids Control is able to provide a one stop solution for all solids control equipment request, as well as the complete mud recycling system. If any request aroused, please feel free to contact with GN.

The closed loop system for treating the drilling waste is now more and more popular and requested by almost all the drilling plant and oil products producers. This week, GN completed the delivery inspection for some drilling waste management equipment including 2 vertical cuttings dryers and 4 decanter centrifuges. These equipment would be used by CNPC for their drilling waste treatment. 
Vertical cuttings dryer and decanter centrifuge are 2 of the main equipment in drilling waste management system. In the same system, cuttings dryer and centrifuge are installed in the same line but one after another in working procedure.

Vertical cuttings dryer is always used to treat the drilling waste cuttings discharged from the primary shale shaker in the solids control system. Discharged cuttings still has large content of drilling fluids that can be recovered for reuse. Besides the drilling cutting, most of the oily sludge treatment also use the cuttings dryer unit for large size solids separation. GN’s cuttings dryer is fixed with screen of 3 sizes. The finest is 250 microns, which means the solids larger than this size would be removed out. Please be noted, the solids less than 250 microns would pass through the screen opening and flow to next procedure with the liquid. After treated by GN vertical cuttings dryer, the OOC will be less than 5%. The effluence coming from the dryer unit needs to be polished by the centrifuge for ultrafine solids separation.

GN big bowl decanter centrifuge could be used in normal solids control system, waste management and some other separation projects. The centrifuge ordered by CNPC is the GN 18 inch model with big capacity and cut point is down to 2-5 microns. The adoption of duplex stainless steel and centrifugal casting technology guarantee the machine stable performance and fewer breaking down for maintenance. 
GN has established the business relation with many of the top class servicer and producer in oil industry. This is not the first time GN got order from CNPC, any request, please feel free to contact with GN.

GN just finished the fabrication of one batch of solids control equipment for a drilling company from Uzbekistan. The ordered equipment mainly includes shale shaker and vacuum degasser. Some drilling companies give the mud recycling service to a third party. However, to reduce the drilling cost, some drilling company will do the mud cleaning by themselves.

Shale shakeris the first stage solids control equipment; the performance of the shale shaker will greatly affect the performance of the complete mud system. The more coarse solids removed at the shale shaker stage, the better the mud system will perform. GN shale shaker has following advantages that ensure the onsite stable performance.

Firstly, the adjustable G force is up to 7.5 with excellent drying performance that will recover more drilling fluids. 
Secondly, the rubber seal installed between the shaker screen and screen support frame is patented. It is easy for installation and replacing. The imbedded rubber strip has good elasticity and chemical resistance for long time application in treating drilling fluids. This type sealing technology effectively avoids the leakage. 
Thirdly, all GN shale shakers have been upgraded to use the composite frameshaker screen that can last for longer time. It reduces the frequency of replacing the screen so that greatly save the cost.

GN vacuum degasser is a type degasser with self-suction function which means no need an extra feeding pump. It is located after the shale shaker to remove the gas in the drilling fluids. It has a long suction pipe inserting into the drilling fluids inside the tank, thus GN vacuum degasser could also be used as a big power mud agitator.

GN’s products have been applied in more than 70 countries and regions. Next year, GN will definitely improve to provide better products and services to all the clients.

The Christmas and New Year are getting closer and closer. GN hopes all clients, no matter Christian or not, will have a good time during these two festivals. Enjoying the time staying with family, everyone would be relax and think about something, something beautiful, bright and hopeful. 
Look back the past one year, GN acquainted many new clients and make friends with them. Moreover, most of them gave their confidence to GN and placed orders for solids control equipment and relative wear parts. In the meanwhile, GN also kept touch with old clients and both parties know each other much deeper. 
In order to give GN’s blessing to all the clients, GN prepared small elegant gifts to all the clients who will help to fill GN’s Customer Feedback Form. GN would like to get the evaluation from all clients and hear about their suggestions. Clients’ feedback is the cornerstone of GN’s development.

How to get the gift from GN

Step 1, Please click below link to download the Customer Feedback Form 
http://www.gnsolidscontrol.com/downloads/Customer-Feedback.docx

Step 2, Fill the customer feedback form
Write down your comments on GN’s products quality, sales representative, after sales service and even the commissioning engineer’s performance on site. Only need to mark a Tick in the form to give your idea. Client can also give their suggestions to help GN to improve.

Step 3, Scan or take a picture of the filled form, send back to GN
For the clients who have specific contact person in GN, the scanned form could be sent via email to the right person. If don’t know where to send, then the filled form could be sent to sales@gnsolidscontrol.com. Don’t forget leave your company information and your physical address for receiving the gift.

Step 4, Waiting gift
Once the customer feedback form was received, GN’s sales person would acknowledge the receipt and arrange the gift delivery. All the gifts are ordered online, and will be sent via international express to door. Clients no need step out the room.

Hurry up or else waiting the gift next year. GN is looking forward your feedback to help us to be much better. , Either praise or criticism, that is the care to GN.

The Christmas and New Year are getting closer and closer. GN hopes all clients, no matter Christian or not, will have a good time during these two festivals. Enjoying the time staying with family, everyone would be relax and think about something, something beautiful, bright and hopeful. 
Look back the past one year, GN acquainted many new clients and make friends with them. Moreover, most of them gave their confidence to GN and placed orders for solids control equipment and relative wear parts. In the meanwhile, GN also kept touch with old clients and both parties know each other much deeper. 
In order to give GN’s blessing to all the clients, GN prepared small elegant gifts to all the clients who will help to fill GN’s Customer Feedback Form. GN would like to get the evaluation from all clients and hear about their suggestions. Clients’ feedback is the cornerstone of GN’s development.

How to get the gift from GN

Step 1, Please click below link to download the Customer Feedback Form 
http://www.gnsolidscontrol.com/downloads/Customer-Feedback.docx

Step 2, Fill the customer feedback form
Write down your comments on GN’s products quality, sales representative, after sales service and even the commissioning engineer’s performance on site. Only need to mark a Tick in the form to give your idea. Client can also give their suggestions to help GN to improve.

Step 3, Scan or take a picture of the filled form, send back to GN
For the clients who have specific contact person in GN, the scanned form could be sent via email to the right person. If don’t know where to send, then the filled form could be sent to sales@gnsolidscontrol.com. Don’t forget leave your company information and your physical address for receiving the gift.

Step 4, Waiting gift
Once the customer feedback form was received, GN’s sales person would acknowledge the receipt and arrange the gift delivery. All the gifts are ordered online, and will be sent via international express to door. Clients no need step out the room.

Hurry up or else waiting the gift next year. GN is looking forward your feedback to help us to be much better. , Either praise or criticism, that is the care to GN.

Good news! Recently, GN solids control published the shaker screen online shopping mall system. By using this system, clients could RFQ or order the screen online easily. To enjoy the convenient of online shopping for GN durable replacement screen panels, please spend some time to learn how to use GN online screen shopping mall.

Step 1: Registration — All clients who want to order the screen online need to register to be a GN screen shopping mall member first. If clients are new here, by clicking the ‘Login’ button on the top right corner of the page, the register process could be started. Only need an effective email ID and general information, then an account is available. After finishing the registration process, clients could log into the account to check the account information, orders placed, desired items in cart etc.

Step 2: Category Selection — GN Solids is able to provide both replacement screen of GN own shale shaker and most of the world well know shaker models. Click the button on top left corner of the page, under GN logo, to find all the replacement screens provided. And then choose the one preferred, the page will turn into the link of order page.

Step 3: Online Inquiry — Detailed information on the shaker screen is published in GN web page. Clients could go through the page to check screen API Nos., part Nos., Conductance as per API RP 13C, and the specifications of the screen as well. Please be noted, GN’s screen has been tested by Third Party laboratory and the report is available. Registered client may ask for the test report once got reply from GN sales team. Client need to choose the right API Nos. and quantity, then submit for a quote. To protect distributors benefit, the neutral package is also available.

Step 4: Order Placing — As GN is willing to provide discount for bulk order, the client would receive the quote via registered email for confidence purpose. After receiving the RFQ, GN will arrange the sales team to follow up with client on detailed request, special preference, discount and delivery time.

More information on GN durable replacement shaker screen, please visit GN’s web. Better doing than thought, no hesitate to register as GN online screen mall member, not only for easy business, but also the enjoyable shopping experience.

P.S. Click below link to learn more about GN composite frame screen promotion policy
http://www.gnsolidscontrol.com/gn-shaker-screen-points-reward-program

As a manufacturer of solids control and waste management equipment, GN Solids Control has the complete production line for fabrication the equipment from raw material of steel cuttings, bending, to lathe processing, then to coating process. At every procedure, GN adopts the up-dated fabrication machine to ensure the quality and efficiency. Recently, GN just upgraded the painting workshop appliances for purpose of both efficiency increasing and environmental protection.

Automatic shot blasting machine – shot blasting machine is used to working piece surface cleaning up and strengthen. It can remove the burr and rust of the casting, so that the subsequent painting process would be performed well.

Constant temperature spraying – In order to increase the paint coverage area on the working piece and outer surface painting quality, GN set up the dust-free and airless painting line. Airless painting machine applies high pressure on the paint, and then the paint was sprayed out via the spray gun as fog style. It can spray the paint to all points of the working piece where the brash will not reach. The thickness of the spray painting is uniform and the consumption is less. Constant temperature would speed up the drying process even in winter.

Electrostatic spraying – the material used in electrostatic spraying is the plastic powder. As the powder coating material has no solvent in it, it will not produce waste of water, gas and solid stuffs. Thus the electrostatic spraying technology is developed fast and nowadays widely applied. Electrostatic spraying also has advantages of high efficiency, suitable for automatic production line and coating powder recyclable.

With a series strict regulations issued on environment protection, many factories stopped their painting job. GN Solids Control is pleased to accept outsourcing painting service with precondition of completion of GN own painting job.