Month: June 2018

Today, GN quality inspectors made the delivery inspection for one batch mud centrifugal pumps and other solids control equipment that would be shipped to a Russia client. These equipment ordered including 6 shale shaker, 2 mud cleaners, 6 centrifugal pumps, 2 centrifugal degasser and 4 decanter centrifuges for 2 rigs.

GN Centrifugal Pump Features
1. Pump spare parts interchangeable with most of the international brand pump for customer easy source
2. Pump casing make from hard ductile iron alloy that increases abrasion resistance capability.
3. Wide open-vane impeller creates lower axial thrust to improve bearing life.
4. High quality non-adjustment mechanical seal to provide zero leakage and longer operation life.
5. All bearing used from top brand for reliable operation.

GN Shale Shaker/Mud Cleaner Features
1. Shaker deck is complete heat treatment to increase the strength
2. Screen supporting frame make from stainless steel for better anti-corrosion feature
3. Composite frame screen matched with longer working time and less knock off to replace the screen
4. Rubber bushing protected damping spring for personnel safe and better rust resistance.
5. Angle adjustable shaker deck could be adjusted during running from either one end with both ends adjusted.

GN Decanter Centrifuge Features
1. Bowl material is duplex stainless steel 2304 that is much better than SS316
2. Bowl is made by centrifugal casting technology for better material distribution and none air blister
3. Screw propeller also from stainless steel with tungsten carbide tile bolted on scraper for protection and long working life.
4. Solids discharging port protected by tungsten carbide bushing
5. Both fixed speed model and VFD model available for customers’ option

GN has more than ten years’ experience in making solids control equipment. Client can get proposal of both single equipment and complex solids control system from GN. Welcome call and ask for a quote.

Recently, GN finished the factory delivery inspection of one set 1000 GPM mud recycling system that will be used in India for big trenchless project. In end of April, GN just shipped out 3 sets 600 GPM mud system to an Asian client who has already had 3 sets mud recycling system from GN.

1000 GPM Mud Recycling System is consisting with following equipment

1. Two units of GN double deck shale shaker GNZS706F for primary solid removing. Double deck shaker is with large capacity due to two-layer screen design for both coarse solids and fine solids separation.
2. De-sander unit GNZS703F-2S is with two sets 10 inch cyclone for sand removing. De-silter unit GNZS703F-12N is with 12 sets 10 inch cyclone for silt removing. The under flow shaker is with same dimension shaker screen for client’s easy shaker screen procurement or inventory.
3. Three sets 40 feet containers are used respectively as mud recycling tank, mud storage tank and mud mixing tank. Other equipment like centrifugal pump, agitator, and mixing hopper are installed on tank and shipped without disassembling them.

With nearly 10 years’ experience in design and manufacturing the trenchless mud recycling system, and sufficient feedback from clients’ onsite application. GN has improved GN compact mud system with stable performance and optimized design. All equipment in the mud recycling system are with advantages in increasing the working efficiency and improving the treating result.

GN is able to provide the mud recycling system used in trenchless project with compact design but self-contained. Other mud system design with plenty of mud tanks for large volume mud storage in oil drilling site, and some economic mud de-sanding unit in small drilling project like water well drilling and piling.

This week, GN is almost finished the fabrication of 8 units solids vacuum pump what would be used in a long distance mud transfer project in Beijing. Now GN’s engineer is the making the last step of delivery inspection and packing.
In client’s project, it is a long distance from the mud pit to the rig. This brought a problem to client how to transfer plenty of mud to where it would be used. The client didn’t get a good solution till they saw GN vacuum pump at the CIPPE show this March.

GN Solids Vacuum pump is a 100 percent pneumatic driving pump that could be used to transfer high solids content sludge like the oilfield drilling waste cuttings, normal drilling mud in recycling system, vessel remaining sludge etc. The other feature of this type pump is the capability to suck and discharge the sludge from and to faraway place.

The client totally order 8 this vacuum pump from GN, and each 4 of them would be installed together to get a large capacity. Besides the pumps, client also ordered 2 empty containers that would be especially used to pack and mount the pumps. Few people will get the idea to put the pump unit into the container. This installation will bring some benefits. All parts of the pump would be covered and protected. All the pumps are installed in the container neatly for convenient operation onsite. This package term is also good for transportation, client only need one time lifting, then 4 pumps can be loaded on the truck. The vacuum pump need air compressor to work, thus the container is provided with air buffer vessel. All suction and discharging pipe manifold are provided and connected, before running onsite, client only need to connect the quick connectors.
GN solid vacuum pump can be used in waste cuttings management system, solids control system, sludge pit cleaning project. For more information, please feel free to contact with GN.

GN Solids America is GN branch located in Houston, USA. It is the first overseas office and warehouse of GN. Regularly, GN will ship from China factory to Houston warehouse for the supplement of GN products inventory there for better support to client from Americas. Now GN has stocked decanter centrifuge and shale shaker unit for sale, welcome contact with GN Houston warehouse for quote and other product information.

GN Solids America LLC
6710 Windfern Road, Houston, TX 77040, USA
+1 (713) 878-0880 / +1 (713) 320-3868 / +1 (713) 320-2103
sales@gnsolidscontrol.com
http://www.gnsolidsamerica.com

Below information on GN stocked decanter centrifuge and shale shaker
Decanter Centrifuge
14 inch bowl diameter with operating speed max up to 3200RPM
Both fixed speed model and VFD model available
Motor and control panel explosion proof standard
One-point lifting pedestal
Application for barite recovery, solids control,dewatering system purpose etc.

Shale Shaker
4-panel screen with area 2.7 Square Meters
Strengthened shaker deck with fully heat treatment and strengthen beam
Embedded rubber sealing with better sealing performance and easy for replacement
SS material screen supporting frame for better anti-corrosion feature

GN also makes inventory for replacement shaker screens in Houston warehouse for client urgent request. Most of the shaker screens stocked are replacement pieces of the widely used brands currently. Welcome to GN Houston warehouse for a look to get more information.